55 Series - FJ55

Wheel Bearing consists of:Cone (bearing) - LM102949Cup (outer race) - LM102910
90080-36067
LM102949/10
Koyo (OEM) - Japan

Brake Hose, Front Outer - Land Cruiser BJ40, FJ40, FJ55- 3/69 to 6/80 - (copper washer seal hose ends)Toyota pn:
96920-32255

Brake Hose, Front Outer - Land Cruiser 40 series - inverted flare ends - 9.25"96910-32305

Snap Ring/Circlip, Outer - Birfield stub shaft - Land Cruiser 1.8mm
Toyota pn:
90520-31010

Toyota - Japan

Tool, Hub Nut Socket 54mm (Toyota 55 mm)
Made in China

Brake Hose, Front Inner - Land Cruiser 40, 55 Series -7/80 - 10.2" Toyota pn:
96940-30265

Universal Joint - Land Cruiser 40, 55, 60, 70 & 80 Series. 64mm u-joint that was used from 1974 (with the introduction of the 4 speed transmission)
04371-36030
04371-60210
Toyota - Made in Japan

Exhaust Hanger Mount, Cushion
Toyota pn:
17567-17010
Toyota - Japan

Washer, Flat (M10) - Toyota Land Cruiser steering knuckle stud.
High strength flat washer.
Toyota pn:
90201-12019
Toyota - Japan

Cone Washer, 8mm for front & rear hub studs. Land Cruiser, Hilux etc. Toyota pn:
42323-60010

Toyota - Japan

8708.29

Pedal Pad, Clutch & Brake - Land Cruiser FJ40, BJ40, BJ42, HJ60/61, FJ60 & others India

Exhaust Hanger Mount, Cushion - ToyotaToyota pn:
17567-61030
17567-17010

Inner Wheel Bearing - Land Cruiser Full Floating front & rear axles
Part numbers:
90368-49084
LM104948 + 910
Koyo - Japan
or NTN - USA

Thrust/Lock “claw” Washer, Spindle Bearing, Front Outer - Land Cruiser 09/1975-on
90214-42030

This kit replaces the two 54mm nuts, the thrust washer, and the locking tab (aka: ‘star washer’) on Toyota Live Front Axles.
Kit Contents:
1x “Star” lock Washer 90215-42025
1x Thrust “Claw” Washer 90214-42030
2x 54mm Spindle Nuts 43521-60011

Lock Washer/Tab, Axle Hub (star washer)
- Land Cruiser All Models from 1976-onThis is the locking washer that holds the front wheel adj
90215-42025

Swivel Hub/Knuckle Kit - Early Land Cruiser 40 Series - FJ40, FJ45, FJ55 1969-09/1975 with the smaller bolt pattern steering arm & with drum brakes.

Note: this kit does not fit models with axles that have been upgraded to Toyota Disc brakes and spind

For front and rear locking hubs, drive plates, and rear full floating axle shafts that use 8.0mm hub studs. Hub Stud Kit:
1x 8x1.25mm Stud
1x 8x1.25mm Nut
1x 8mm Lock Washer
1x Cone Washer

Toyota pn: 90116-08325
Made in Japan by Joint Fuji

Nut for Steering Knuckle Stud, drun brake backing plate & other high strength applications. Land Cruiser, Hilux & othersM10x1.25
Toyota pn:
94115-71200 plated
Toyota - Japan

Steering Knuckle Stud - “hexalobular” (=has 6 point male torx at the top for tightening into place).
Toyota pn:
90126-12010 (current pn)
90126-12005
90116-12007
Toyota - Japan

Snap Ring/Circlip, Inner - axle shaft into birfield - Land Cruiser 40, 50, 60, 70 Series & Hilux solid axleToyota pn:
90520-27091

Toyota - Japan